no hdmi output – randomly stopped

Forum › Forums › Freesat HD › HDR 1000, 1010, 1100S › no hdmi output – randomly stopped

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • December 29, 2012 at 8:28 pm #14138
    Anonymous
    Inactive

    Hi,

    Went to watch some telly the other day and my hdr1000s was on, but when I turned the TV on there was no HDMI output… I changed the cables, changed the source selection on the tv, even tv back off then on, I then put the freesat into standby and then back on – still no hdmi output. The TV simply said, “no signal.”

    – the only thing that would fix it, is taking power cable out the back of the freesat box, and then back in.

    all works now

    anyone else experienced this? and why?

    December 29, 2012 at 9:15 pm #41124
    Anonymous
    Inactive

    No, but if you post TV brand and model it might give insight if there are more posts.

    January 2, 2013 at 7:35 pm #41125
    Anonymous
    Inactive

    I get this , but its when the box has gone into standby.

    I’ve tried different leads but it make no difference :(

    I have to do the same and pull the power on the humax box and then it works again.

    I have a LG plasma TV

    January 2, 2013 at 7:37 pm #41126
    Anonymous
    Inactive

    does yours change the tv settings and lower the quality ?

    mine goes back to 480 when it was set to 1080p but after it crashes I can only set 1080i

    I have to unplug eveything ang rescan the channels and then I get 1080p again

    January 3, 2013 at 8:05 am #41127
    Anonymous
    Inactive

    bluealien – What brand and model of TV?

    January 3, 2013 at 1:23 pm #41128
    Anonymous
    Inactive

    I’m having a similar problem, but it only happens when the box is recording and I power it on from standby. The box is connected to my Yamaha RX-V667 amp. My TV is getting the signal from the amp.

    Whenever it’s not recording it powers on fine.

    January 3, 2013 at 11:56 pm #41129
    Anonymous
    Inactive

    Hi Repassac

    the TV is goodmans 42″ Plasma

    January 4, 2013 at 10:35 am #41130
    grahamlthompson
    Participant

    bluealien – 1 day ago  » 

    does yours change the tv settings and lower the quality ?

    mine goes back to 480 when it was set to 1080p but after it crashes I can only set 1080i

    I have to unplug eveything ang rescan the channels and then I get 1080p again

    1080p isn’t always the highest quality setting. All transmissions are 1920 x 1080 interlaced. Either you let the box de-interlace or the TV does it. In most cases there is little difference unless the TV has poor de-interlacing.

    Can you actually see a picture improvement by selecting 1080p ?.

    If not leave the box on 1080i. Problem is most likely TV is reporting back during the hdcp handshake it can only do 480p.

    Check with the TV maker to see if there’s a firmware upgrade fix.

    January 4, 2013 at 10:36 am #41131
    grahamlthompson
    Participant

    bluealien – 10 hours ago  » 

    Hi Repassac

    the TV is goodmans 42″ Plasma

    Check to see if there’s a firmware upgrade for the TV, see the above post

  • Author
    Posts
Viewing 9 posts - 1 through 9 (of 9 total)
  • You must be logged in to reply to this topic.

The inner genius!