- This topic has 10 replies, 5 voices, and was last updated 9 years, 2 months ago by
.
-
Posts
-
Hi my name’s Dick. I’m new here having just bought a HDR-1010S.
The box works well and apart from the funny green writing on the TV guide
I’m more than happy with it.
One thing I can’t sort out though is that after being on Stand-by for several hours the box
will not switch on. I have to pull the plug and reconnect to get it to work.
Anyone got any ideas?
Thanx
Hi and welcome to our forum. First thing to try is a reset to factory defaults. Settings – System Settings – Factory Default.
Make a note of your recording schedule or photograph it with a digital camera first, as you will have to re-enter it after the reset.
Tried a reset twice already but it hasn’t solved the problem.
DickF – 11 minutes ago »
Tried a reset twice already but it hasn’t solved the problem.
Strange. I take it the box won’t boot from the remote or the box power button ? Try pressing the zero button on the remote a couple of times to boot the box. If you have the newer RM108U remote does the stb button flash red when you try to boot the box ? Does turning off low power sby make any difference ?
Pressing the Zero on remote does nothing except showing a 0 on the screen. Power off switch on box does switch the box on and off as long as I’m not in the phase where it wont switch on. The STB button flashes red when pressing any button on the remote. At oresent the settings are Automatic power down “on” and Standby mode “power save” Should I turn the Automatic power down to “off”?
DickF – 7 minutes ago »
Pressing the Zero on remote does nothing except showing a 0 on the screen. Power off switch on box does switch the box on and off as long as I’m not in the phase where it wont switch on. The STB button flashes red when pressing any button on the remote. At oresent the settings are Automatic power down “on” and Standby mode “power save” Should I turn the Automatic power down to “off”?
A bit puzzled, if the box is in sby then how does pressing zero on the hdr1010S show anything on the screen (pressing the 0 key will boot the box as well as the power toggle button and you can push it several times unlike the power toggle) ? Up to you if you turn off power save. If you don’t the box will shut down after no remote keys pressed for 3hrs (which can be a pain in the neck). As to turning off low power sby I was just interested to see if it affects the box not booting after being in sby.
My fault, didn’t catch that the box should be in sby, my mistake.
Will try the alternative settings and get back to you. Thanx for all your help so far
When you’re “in the phase where it wont switch on” does the red light on the box remain red and no channel is displayed on the box display? Or is it the case that the TV simply does not display the output from the box?
Additionally try disabling HDMI-CEC on your TV.
Trade names for CEC are Anynet+ (Samsung), Aquos Link (Sharp), BRAVIA Link and BRAVIA Sync (Sony), HDMI-CEC (Hitachi), E-link (AOC), Kuro Link (Pioneer), INlink (Insignia), CE-Link and Regza Link (Toshiba), RIHD (Remote Interactive over HDMI) (Onkyo), RuncoLink (Runco International), SimpLink (LG), T-Link (ITT), HDAVI Control, EZ-Sync, VIERA Link (Panasonic), EasyLink (Philips), and NetCommand for HDMI (Mitsubishi).
Yes exactly. The red light in the chromed on/off swich is glowing but no writing re channel or freesat is shown on the box display. And I can press the switch as many times as I like but the box does not respond until I pull the power plug and repower up.
Did anyone solve this problem? My 1010S is now 14 months old and has worked perfectly up to this point but now I am experiencing the same problem as described above. Once the box has been in standby for a day or so then neither the remote control nor the front panel on/off switch will turn it on. I have even tried automatically turning it on at a set time using the power-on function, but it still will not turn on. The only solution is to unplug it and then restart it. I think I have also missed some recordings when this happens but need to do more tests to confirm this. I have tried resetting it to factory defaults but this does not solve the problem. Presumably this is a software issue. It is still under Humax 2 year warranty so if there is no simple fix then I may have to contact them.
- You must be logged in to reply to this topic.