Downgrade Raydons Software

Forum › Forums › Freesat HD › FOXSAT HDR › Downgrade Raydons Software

Tagged: 

Viewing 13 posts - 1 through 13 (of 13 total)
  • Author
    Posts
  • June 7, 2013 at 4:28 pm #14663
    Anonymous
    Inactive

    Hi How do remove or downgrade Raydons Software, as i am having lots of problems.

    Many Thanks

    Nitramhdr

    June 7, 2013 at 4:38 pm #44053
    grahamlthompson
    Participant

    What problems ? It’s very unlikely the CF is to blame. It doesn’t change the way the box works when not used with a PC, nor alter the existing software apart from a different message when booting the box.

    In fact retaining it is likely to make it easier to find out what the problem is.

    June 7, 2013 at 5:37 pm #44054
    aldaweb
    Participant

    Hi Nitramhdr and welcome to the forum :-)

    I assume this is for the Foxsat HDR so moved to the correct Forum

    June 7, 2013 at 7:00 pm #44055
    Anonymous
    Inactive

    Yes sorry forgot to say its a foxsat HDR!

    I am not seeing any of the recorded program’s although the hard drive

    Is a 37%.

    It dose not always do this but when it plays up I power down at the

    Wall and I can see program’s again!

    Thanks

    Nitramhdr

    June 7, 2013 at 7:09 pm #44056
    grahamlthompson
    Participant

    nitramhdr – 4 minutes ago  » 

    Yes sorry forgot to say its a foxsat HDR!

    I am not seeing any of the recorded program’s although the hard drive

    Is a 37%.

    It dose not always do this but when it plays up I power down at the

    Wall and I can see program’s again!

    Thanks

    Nitramhdr

    Firstly try a factory reset.

    If it’s not still under warranty.

    With the power off, remove the lid and the HDD carrier. Try removing and re-seating the cables connected to the HDD. It could be just a intermittent bad connection.

    If you aren’t already on CF 1.04.11 reflash to the latest version.

    The CF won’t be the cause of the problem.

    June 8, 2013 at 5:26 am #44057
    Anonymous
    Inactive

    Ok got up at 5.30am today removed the hard drive and cleaned all the pins cables that I could see, next thing to do is look for the software update (flash) my software version is HPRSFCI 1.00.21 how do I upgrade the the latest version!

    Thanks.

    June 8, 2013 at 6:05 am #44058
    Anonymous
    Inactive

    I believe v1.00.21 is the latest (and probably final) official release for the HDR.

    http://beta.humaxonline.co.uk/downloads/foxsat-hdr

    June 8, 2013 at 8:58 am #44059
    grahamlthompson
    Participant

    nitramhdr – 3 hours ago  » 

    Ok got up at 5.30am today removed the hard drive and cleaned all the pins cables that I could see, next thing to do is look for the software update (flash) my software version is HPRSFCI 1.00.21 how do I upgrade the the latest version!

    Thanks.

    If you have installed the Custom Firmware 1.0.11 it will also have installed the latest Humax Firmware 1.0.21 as part of the process anyway.

    June 9, 2013 at 1:29 pm #44060
    Anonymous
    Inactive

    I’ve removed the hard drive and cleaned the cables etc, but I still have the same problem! What do I do now?

    Thanks

    June 9, 2013 at 1:44 pm #44061
    Anonymous
    Inactive

    Did you do a factory reset as Graham suggested?

    If yes, then I would try running the CF disk-fix utility to see if disk problems exist.

    June 9, 2013 at 5:40 pm #44062
    Anonymous
    Inactive

    Yes did the factory reset,

    So sorry but how and where do I get/ use the CF disc fix?

    Thanks

    June 9, 2013 at 5:49 pm #44063
    Anonymous
    Inactive

    See the package documentation (http: to the web interface and choose the documentation icon)- I don’t have access to my unit until tomorrow but I am sure it is covered.

    Anyway, basically you issue a disk-fix command (Think it has a hyphen) and the box will start in maintenance mode

    June 9, 2013 at 8:18 pm #44064
    raydon
    Participant

    REPASSAC – 2 hours ago  » 

    See the package documentation (http: to the web interface and choose the documentation icon)- I don’t have access to my unit until tomorrow but I am sure it is covered.

    Anyway, basically you issue a disk-fix command (Think it has a hyphen) and the box will start in maintenance mode

    Yes, it does have a hyphen, but it’s fix-disk, not disk-fix.

  • Author
    Posts
Viewing 13 posts - 1 through 13 (of 13 total)
  • You must be logged in to reply to this topic.

The inner genius!