Barry

Forum Replies Created

Viewing 15 posts - 4,861 through 4,875 (of 5,284 total)
1 2 3 … 324 325 326 … 351 352 353
  • Author
    Posts
  • December 14, 2011 at 5:03 pm in reply to: Remote control has stopped working – unit failing to respond. #28759
    Barry
    Moderator

    Welcome to the Forum David :-)

    9150 OTA is being repeated from 10am Friday 16th

    If your customers cannot wait until upload via serial port would have to be carried out.

    I am surprised by the number affected, there are either lots who leave their boxes on 24/7, or who have had a problem with the OTA but have done nothng about it.

    December 14, 2011 at 3:23 pm in reply to: Remote control has stopped working – unit failing to respond. #28756
    Barry
    Moderator

    Welcome to the Forum :-)

    I suspect it is not your remote that has stopped working.

    Was informed an hour ago of a possible problem, and have been working on it.

    So far have this to report – boxes appear to lock up if using software version 1.00.19 or earlier, now trying to establish which mux/channel is causing it.

    Watch this space.

    Edit:

    OK not going to be able to tie it down to a channel or mux as it happens on a few.

    For the OP

    What model of PVR and what version of software does your unit have on board…if it locks to quickly for you to check, then disconnect aerial, and try.

    The bottom line for anyone with the problem is to update software to latest versions. 9300 latest is on air now.

    December 13, 2011 at 8:53 am in reply to: Update Log for Record/Watch Apps #24148
    Barry
    Moderator

    A change that must have happened yesterday but my V13 unit did not pick up, until this morning.

    Chan 875 has changed name to PlayboyTV Chat

    December 13, 2011 at 8:51 am in reply to: Improvements thanks to 1.02.20 #27424
    Barry
    Moderator

    Humax Towers are aware of the AD problem..

    December 12, 2011 at 11:36 am in reply to: Volume level #28740
    Barry
    Moderator

    Welcome to the Forum :-)

    Have you tried increasing the volume output from the Humax, the default is about half.

    December 10, 2011 at 5:08 pm in reply to: Unable to use with analogue signal #28716
    Barry
    Moderator

    Welcome to our Forum :-)

    Try pressing exit on the ‘no channels’ popup, you should then be taken to the Installation menu, press left arrow, and you should be able to scroll up to record menu, and playback recorded programmes.

    December 8, 2011 at 12:03 pm in reply to: Update Log for Record/Watch Apps #24146
    Barry
    Moderator

    Just had the pop up on V13

    1 channel removed

    725 – Abs C Rock

    A bit strange removing just one of their channels :?:

    December 7, 2011 at 6:43 pm in reply to: ITV1-HD screws up again ? #28344
    Barry
    Moderator

    Appears to be fixed now for the region I receive.

    December 7, 2011 at 4:58 pm in reply to: IPTV Channels not Enabled #28668
    Barry
    Moderator

    This is my own personal take on the matter.

    The Freeview HD units, when released, conformed to the spec as was. There is no obligation for manufacturers to put resources into changing/updating software to support later channel launches etc.

    However I will ask Humax Towers if they have any plans to support these channels.

    December 7, 2011 at 4:16 pm in reply to: AV2HDR-T2 v1.0 for the Humax HDR Fox T2 #28691
    Barry
    Moderator

    Excellent stuff, many thanks. Downloaded, will have a play later.

    December 7, 2011 at 8:03 am in reply to: Ghosting #28592
    Barry
    Moderator

    Welcome to the Forum :-)

    First things to check would be the scart cable/connection:

    Are you using a decent quality fully screened scart cable (some of the cheaper ones can suffer from ‘crosstalk’)

    Is it in the correct socket on the 9150.

    Is it fully pushed home at both ends.

    Then check that RGB is enabled on the unit.

    December 6, 2011 at 3:05 pm in reply to: Update Log for Record/Watch Apps #24145
    Barry
    Moderator

    Thanks for the confirmation Graham :-)

    December 6, 2011 at 2:31 pm in reply to: Update Log for Record/Watch Apps #24143
    Barry
    Moderator

    I think the changed one is:

    Chan 691 – DAYSTAR TV moved to 11261 H

    December 6, 2011 at 2:19 pm in reply to: Update Log for Record/Watch Apps #24142
    Barry
    Moderator

    Pop up on V13 unit:

    Added – 5

    Changed – 1

    Added – All on 10964 H

    Chan 128 – Channel 5+1

    Chan 129 – 5 USA

    Chan 130 – 5 USA+1

    Chan 131 – 5*

    Chan 132 – 5*+1

    Still checking the changed one, bit busy :-)

    December 6, 2011 at 12:47 pm in reply to: ITV1-HD screws up again ? #28343
    Barry
    Moderator

    ITV have acknowledged my message and passed on to technical team.

  • Author
    Posts
Viewing 15 posts - 4,861 through 4,875 (of 5,284 total)
1 2 3 … 324 325 326 … 351 352 353

The inner genius!